MATRIX VISION - mvBlueFOX3 Technical Documentation
mvBlueFOX3-1013 (1.3 Mpix [1280 x 1024])


The sensor uses a pipelined global snapshot shutter, i.e. light exposure takes place on all pixels in parallel, although subsequent readout is sequential.

Feature Description
Manufacturer E2V
Sensor name EV76C560
Max. frames per second 60
Device Structure CMOS image sensor
SNRmax [dB]1/ 39
DNR (normal / HDR) [dB]1/ 50.5 / > 100 dB
Image size 1/1.8
Number of effective pixels 1280 (H) x 1024 (V)
Unit cell size 5.3µm (H) x 5.3µm (V)
ADC resolution / output 10 bit → 8/10/(12)

1 Measured accord. to EMVA1288 with gray scale version of the camera

Spectral Sensitivity

Figure 1: mvBlueFOX3-1013G
Figure 2: mvBlueFOX3-1013C

Enhanced version

Figure 1: mvBlueFOX3-1013GE


Name Value
InternalLineLength 944
InternalADCClock 118.75

Free running mode

To calculate the maximum frames per second (FPSmax) in free running mode you will need following formula:

                                           2             ImageHeight + 10 
ReadOutTime =  InternalLineLength * ---------------- * (-----------------)
                                    InternalADCClock          1000

If exposure time is lower than frame time:

FPS_max =  -------------

If exposure time is greater than frame time:

FPS_max =  --------------

Snapshot mode

To calculate the maximum frames per second (FPSmax) in snapshot mode you will need following formula:

                                           2             ImageHeight + 10 
ReadOutTime =  InternalLineLength * ---------------- * (-----------------)
                                    InternalADCClock          1000
FPS_max =  ----------------------------
            ReadOutTime + ExposureTime

Line scan mode

The sensor offers also a usage as a line scan sensor. One (gray scale sensor) or two lines (in terms of color sensor) can be selected to be read out of the full line height of 1024 lines. This or these lines are grouped to a pseudo frame of selectable height in the internal buffer of the camera.

The camera then outputs these frames which contain multiples of the same scan line(s) without gaps or interruptions.

To operate in line scan mode, use the following properties:

  • In "Setting -> Base -> Camera -> !GenICam -> Device Control", please change the Device Scan Type to Linescan.
  • In "Setting -> Base -> Camera -> !GenICam -> Image Format Control", please set Width and Height. Height specifies how often the same line(s) will be used to reach the height of the image.
    Use Offset X to shift horizontally the starting point of the exposed line.
    Use and Offset Y to shift the scan line vertically.
The sensor will not get faster by windowing in x direction.
  • Finally, in "Setting -> Base -> Camera -> !GenICam -> Acquisition Control", please adapt the Exposure Time.
    The exposure time as to be low and max. approx. 60 us in order to achieve the max. line scan rate of 12.6 kHz.

You may use longer exposure times at the expense of scanning frequency.

Using more than one line e.g. 5, is like having an area scan with ImageHeight = 5. In line scan mode, the max. ImageHeight is ≤ 16.
You can use either Continuous or a trigger mode as Acquisition Mode in "Setting -> Base -> Camera -> GenICam -> Acquisition Control". However, if an external (line) trigger will have to be used, it is absolutely required that the external trigger is always present. During a trigger interruption, controlling or communication to the camera is not possible!

Frame rate calculator

Frame rate calculator
Mode: Overlapping exposure and readout
Image bit depth:

Image width: pixels
Image height: pixels
Exposure time: us
Device throughput: Device Sensor Throughput
Device Link Throughput
Link speed:
Frame rate (max): 1/s

Device Feature And Property List